WIRELESS SYSTEMS

Transmitters
Receivers
Antennas
Bags & Cases
Miscellanous

ACCESSORIES FOR TRANSMITTER
Belt Clip for SM/SMa

• Stainless Steel Spring Clip

• Machined Aluminum Bracket

The SMBCUP/DN is an accessory belt clip that attaches to the SM/SMa transmitter with a set screw, allowing the transmitter to be worn on a belt or other wardrobe item where a low profile is required.

There are two models of SMBC (SM Belt Clip), SMBCUP, which has the antenna pointing up when the SM is worn on a belt, or SMBCDN, which has the antenna facing down. There are two separate models required because of the assymetrical shape of the SM transmitter.

Prod.nr.:	Description:
SMBCUP	Accessory belt clip for attaching the SM with the antenna pointing up

Prod.nr.:	Description:
SMBCDN	Accessory belt clip for attaching the SM with the antenna pointing down

Download: Technical Data

The SMDBC can be installed in one of two positions, allowing the antenna to be facing up or down, depending on the requirements of the user.

Prod.nr.:	Description:
SMDBC	Accessory belt clip for attaching the SMD and SMQ transmitters

Download: Technical Data

Battery Eliminator for SM-Series

Remote Control for SM-Series

Prod.nr.:	Description:
RM	Lectrosonics Remote Control for SM transmitters. MORE

Download: Technical Data

Prod.nr.:	Description:
RM2	Lectrosonics Remote Control for SM transmitter Low cost

Download: Technical Data

Plug on Transmitter

Prod.nr.:	Description:
MCA5X	Lectrosonics connector for Plug on transmitter XLR3-M to TA5F

Download: Technical Data

Lavalier Microphones

Prod.nr.:	Description:
M152/SM5P	High performance omnidirectional model with locking 5 pin (Switchcraft TA5F) plug and water resistant boot for SM transmitter

Prod.nr.:	Description:
SMKITTA5	Microphone adapter kit includes instructions, sleeve, tubing and TA5F connector,            plus two each 1.5 kOhm and 3.3 kOhm resistors

Download: Technical Data

ACCESSORIES FOR SR RECEIVER

Prod.nr.:	Description:
SRSNY/E	Adapter kit for Sony® camera slots. * Includes bezel, hardware and rear panel DB15 connector wired for power and audio connections

Prod.nr.:	Description:
SRUNI/E	Adapter kit for Unislot camera slots such as those provided on Ikegami and Panasonic cameras. * Includes bezel, hardware and rear panel DB25 connector wired for power and audio connections.

Prod.nr.:	Description:
SREXT/E	This kit includes a rear panel with two TA3 male jacks for the balanced outputs and a power jack with a locking connector. Trim the power cable to the desired length.

Download: Manual

Prod.nr.:	Description:
SRHARNESS	The two balanced audio outputs and the power cable are secured to the panel with rugged strain reliefs. Cables are 6 feet long and audio cables are shielded. No connectors are provided.

Download: Manual

Prod.nr.:	Description:
MCSRXLR	12 inch long TA3 female to XLR male 3-pin for balanced output

Accessory kit for building a single right angle 3-pin or 5-pin TA Series connector for transmitter inputs or SR receiver outputs. Kit includes large and small backshells, two different inserts and strain relief sleeves.

Prod.nr.:	Description:
RATPAC	Connector kit, right angle shell for TA3/5 F

The SR receiver can be powered by L and M type rechargeable video camera batteries for stand-alone or on camera use with an optional “battery sled” adapter. The adapter includes two balanced outputs with TA3M connectors and a locking power jack with an integral switch that disconnects the battery when a plug is inserted. The charger supplied with the battery must be used since the battery sled does not include charging circuitry.

Prod.nr.:	Description:
SRBATTSLED	Optional “battery sled” adapter

Download: Manual

Prod.nr.:	Description:
SRSLEEVE	This sleeve is supplied with Velcro swatches for mounting the SR Dual Receiver on a flat surface of camera, cart, rack, etc. The sleeve is sized and lined for a snug fit in a vertical or horizontal position. MORE

Download: Manual

Prod.nr.:	Description:
SRHARDWARE KIT	Kit for SRSLEEVE includes spare retaining pin

Download: Manual

Prod.nr.:	Description:
MCSR/5PXLR5P	Right angle TA5 on the receiver end and a 5-pin, full-size XLR male on the other end. Includes set screws and hex wrenches. 25" long.

Balanced XLR male to stripped and tinned leads. 20 dB attenuation as supplied. Solder bridge jumpers provided to select 30 dB or 40 dB attenuation. 6 ft. long. Commonly used with the Venue receiver to achieve a mic level output

Prod.nr.:	Description:
MCAXLRATTEN	Cable, attenuation, 6 ft to XLR M

Prod.nr.:	Description:
MCSRPT	Cable, TA3F to tails, 15"

Prod.nr.:	Description:
MCSRTRS	Cable, 2) TA3F to 1) TRS, 12" for camera inputs

Prod.nr.:	Description:
MCVRFIELD	Cable, XLRF, right angle to mic cable with stripped, tinned leads, 3 ft.

Prod.nr.:	Description:
PS301	Power cable, 12”, Hirose4 to DC Coax

Prod.nr.:	Description:
PSLZR	Power cable; right-angle locking LZR type plug to stripped and tinned leads, 6 ft. long

ANTENNAS
ALP Series

The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth, allowing coverage of the entire UHF band used for Lectrosonics wireless microphone and IFB systems.

These antennas provide between 4 and 6dB of RF gain in the forward direction, depending on the operating frequency.

Prod.nr.:	Description:
ALP500	Economical design with uncovered connector, frequency range: 450-862 Mhz

Prod.nr.:	Description:
ALP620	Skeletonized design for low wind resistance when used in mobile applications, frequency range: 450-862 Mhz

Prod.nr.:	Description:
ALP650	Amplified design for use with long antenna cable runs, available in frequency range: ALP650L/E (RoHS compliant) 470.000 - 692.000 MHz ALP650M/E (RoHS compliant) 537.000 - 768.000 MHz ALP650H/E (RoHS compliant) 640.000 - 862.000 MHz

Download: Technical Data

Dipole Antennas

A unique and very useful design, the PCA900 antenna provides wide bandwidth and a circular pattern in a compact, rugged package. A BNC connector allows direct connection to receivers and multicouplers with standard 50 ohm coaxial cable. An aluminum mounting strap for fixed installation is included and a variety of other mounting options are also available for mobile applications.

Specifications

Antenna type:	Directional dipole
Frequency range:	825 - 1025 MHz
Gain:	3.7 dB approx.
Dimensions:	5.63 x 3.88 x .500 inches
Weight:	1.7 ozs (without strap and hardware)
Included accessories:	Aluminum strap with four mounting screws

Prod.nr.:	Description:
PCA900	Dipole antenna PCA900/2 Dipole antenna, pair

Download: Technical Data

Collapsible dipole antenna, adjustable from 550 MHz to 800 MHz. SWR is less than 2:1 at +/- 50 MHz from the center frequency. Ideal for situations where a full 360 degree receiving pattern is required (as opposed to a directional pattern). Includes mounting kit.

Prod.nr.:	Description:
SNA600	Collapsible dipole antenna kit

Download: Technical Data

ALP Series and SNA600 antennas all include a 50 Ohm BNC connector and a 3/8”-16 stainless steel mounting stud. The mounting stud adapts these antennas for use with the optional mounting adapter kit. Also works with the discontinued ALP700A.

Prod.nr.:	Description:
ALPKIT	Mounting Kit for ALP/SNA

Prod.nr.:	Description:
A500RA(xx)	UHF flexible whip antenna with right-angle BNC, specify frequency block, (last two digits (xx) for example: A500RA21, A500RA22, etc.), (pair shown)

Prod.nr.:	Description:
A500RA	Antenna, UHF, right angle, 470-608 MHz

Prod.nr.:	Description:
A8Uxx	antenna, UHF, w/BNC connector, specify frequency block, (last two digits (xx) for example: A8U21, A8U22, etc.), (pair shown)

Download: Manual

Prod.nr.:	Description:
AMM Kit	UHF transmitter antenna kit for 200 Series, 400 Series and 700 Series digital transmitters SMA plug

Download: Manual

Prod.nr.:	Description:
AMM(xx)	UHF top-mount antenna cut to specific block for 200 Series, 400 Series and 700 Series digital transmitters, SMA plug, specify frequency block, (last two digits (xx) for example: AMM21, AMM22, etc.)

The BiasT is used to apply DC power to a coaxial antenna line for remotely powering the UFM230 filter/amp. The DC power applied to the BiasT (9 to 16 VDC) appears on the input port of the BiasT to power the UFM230 through the coaxial cable, but is isolated from the output port so it will not be applied to the input of the receiver.

The BiasT is normally placed near the receiver being fed by the coaxial cable, where power is available. The UFM230 filter/amp and antenna are placed at the opposite end of the coaxial cable, close to the antenna.

Power supply (not included with BiasT)
110V AC input
12V DC regulated output required for powering the BiasT
(CH20, DCR12/A8U and DCR12/A4U will work.)

Prod.nr.:	Description:
BiasT	DC power inserter for active antennas

Download: Manual

POUCHES & CASES

Prod.nr.:	Description:
PR1A	Leather pouch for IFB R1A receiver, provides a belt clip

Prod.nr.:	Description:
CCMINI	Zippered carrying case for compact wireless systems (batteries and screwdriver not included)

Prod.nr.:	Description:
CCIS400	Waterproof case for R400A and IM transmitter

Prod.nr.:	Description:
CCTM400	Waterproof case for R400A and UH400TM transmitter